4.3" Latest NanoVNA NanoVNA-F HF VNA VHF Network Analyzer Case w/ RF Demo SN Kit

Description

Welcome to smartway
4.3" Latest NanoVNA NanoVNA-F HF VNA VHF Network Analyzer Case with RF Demo Kit
Description
Latest NanoVNA NanoVNA-F VNA HF VHF UHF Vector Network Antenna Analyzer + 4.3 inch IPS LCD + Metal Case +
RF Demo Kit
New
laser typing case
is arriving, new
1.5GHz
measurement frequency on sale~~~
support measurable frequency to 1.5 GHz, default setting 1 GHz, accurate measurement up to 1.35GHz.
Product Description:
NanoVNA-F Mini Vector Network Analyser is a product based on the Open Source Project of NanoVNA (https://ttrf.tk/kit/nanovna/). The RF part is consistent with the original version (NanoVNA-F uses harmonic spread measurement
frequency to 1 GHz
).
NanoVNA-F hardware functions include and are not limited to the following improvements:
1. Use
4.3-inch IPS TFT LCD
screen, with a larger view angle and can be seen clearly in strong outdoor light.
2. Switch to large capacity
5000mAh lithium batter
y, standby time is longer, and expand a USB interface. Usually, it can be used as a rechargeable treasure when the instrument is not used.
3. The IC is charged by high current 2A, and the charging time is shorter.
4. Change to larger and better operating wave wheel.
5. Switch to a power switch with a greater sense of operation and a better sense of operation.
6. Support Chinese and English menu switching;
7. Upgrade the user program by virtual U disk.
8. Standard aluminium shell to protect SMA head and reduce the interference of external electromagnetic wave to instrument.
8. Software open source github.com/flyoob/NanoVNA-F
The hardware block diagram of NanoVNA-F is as follows
NanoVNA-F measurement range is
50k-1GHz
. The harmonic spread measurement frequency of the output signal of the clock chip SI5351 is 1000MHz. At 600M-1GHz, the dynamic range of S11 is 40dB (standing wave ratio is less than 1.02). At the same time, a metal shield is designed for the RF front-end, so that the dynamic range of S21 is better than 60dB in the whole frequency band.
Features
:
Dimensions: 14CM * 7.5CM * 2CM (length, width and height)
Measuring Frequency: 50kHz ~ 1000MHz
RF output: - 13 DBM (maximum - 9 dbm)
Frequency accuracy: < 0.5 ppm
Port SWR: < 1.1
Display: 4.3 inch IPS TFT (800x480)
USB Interface: USB Type-C Communication Mode: CDC (Serial)
Power consumption: USB 5V 200mA, built-in 5000mAh battery, theoretical life of 18 hours, maximum charging current 2A
Output capability: 5V/1A, supporting Android and Apple phones
Number of calibration points: 101
Number of scanning points: 101
Display Tracking: 4, Mark: 4, Settings Save: 5
Scanning time: about 1.9s/time (50kHz-1000MHz full frequency band)
Measurable S parameters, voltage standing wave ratio SWR, phase diagram, group delay, Smith circle diagram... ;
19.0Wh (about 5000mAh after conversion) large capacity lithium battery
Designing a metal shield for the RF front end, allowing the S21 to have a dynamic range better than 60dB over the full frequency range
power bank fuction: 5V/1A ,
Supporting Android and Apple Mobile
Open route length test:
NanoVNA-F S11 parameter, SWR standing wave ratio test
UV9D antenna U-band standing wave ratio measurement, starting frequency: 300M, termination frequency: 600M, standing wave minimum frequency 441.000000MHz, SWR = 1.03.
S21 insertion loss measurement, low pass, high pass, band pass filter measurement
Measuring 6.5M Ceramic Notch with NanoVNA-F
Measuring 10.7M ceramic filter using NanoVNA-F
A self-made low-pass filter was measured using the NanoVNA-F with a 3dB bandwidth of approximately 400MHz.
Performance comparison, E5071C four-port vector network vs NanoVNA-F
RF Demo Kit For NanoVNA RF Test Vector Network Tests Filter/ Attenuator
Features:
Made of fine quality material, practical, has a long service life.
Compact and lightweight, easy to operate and use.
This is a vector network analyzer learner tool.
Can be used with NanoVNA-F to measure 6.5M ceramic notch filter.
Can be used with NanoVNA-F to measure homemade low-pass-filter, 3dB bandwidth about 400MHz.
Specifications:
Material: PCB
Color: green
RLC series and parallel circuit 1
RLC series and parallel circuit 2
33 ohm resistance, SWR=1.5
75 ohm resistance, SWR=1.5
BSF ceramic notch filter, center frequency 6.5MHz
BPF ceramic filter, centre frequency 10.7MHz
RC series circuit
LC series circuit
Capacitor
Inductance
Homemade low-pass filter, 3dB bandwidth 400MHz
Homemade high-pass filter, 3dB bandwidth 500MHz
Short-circuit calibration circuit
Open-circuit calibration circuit
50 ohm load calibration circuit
Straight-through
10dB attenuation circuit
3dB attenuation circuit
Each set of functional circuits
Item size: 100 * 100mm / 3.9 * 3.9in
Item weight: 38g / 1.3ounce
Package size: 159 * 152 * 52mm / 6.3 * 6.0 * 2.0in
Package weight: 106g / 3.7ounce
Package List：
1X Nanovna meter
● 2X SMA-JJ RG316 cable 20CM(NanoVNA-F is a standard SMA female connector, which is used to switch to M head and N head to better protect SMA female)
● 1 setX calibration parts (50Ω standard load x1, open circuit calibration piece x1, short circuit calibration piece x1, use the included calibration piece, the instrument can be calibrated to get good measurement result data)
● 1X SMA-JJ double needle
● 1X SMA elbow external screw inner hole to inner screw inner needle
● 1X Type-C data cable
●
1X PCB RF Tester Board
●
2X 200mm Adapter Cable
About us
1.Payment
We accept Paypal ONLY.
2.Shipping.
1).We ship to most of countries in the world. Item will be post to customer's ebay address within 1 working after payment arrive.
2).Item will be sent with tracking number when order value is over USD16. Or we'll ship order without tracking number.
3).Pls leave a note or send a message if any question.
3. Tax
Import duties, taxes and charges are not included in the item price or shipping and handling. These charges ore the buyer's responsibility.
4. Return
We understand that not every purchase is a good one for every custome
Please note that we only accept returns within 30 days after delivery.
a).If the item is defective/DOA (Dead on Arrival) we must be notified within 2 days of arrival, and a refund in full will be granted after item is sent back.
b).Returns after 30 days will not be accepted.
c).Please allow up to 3 business days for your item to be inspected and your return to be be processed.
5. Working Time
We work from Monday to Friday. We'll reply message within 24 hours during working time and 48 hours during vacation. We'll do best to solve problem, don't worry.
On Jun-01-21 at 13:41:06 PDT, seller added the following information: